Ruptela - Installation Guide
Installing a GPS tracking device in your automobile is not an advanced task, but it surely is crucial to take security precautions, as such the installation should solely be carried out by a qualified Auto Electrician. Usually, it takes roughly 2 hours to set it up relying on the complexity of the vehicle’s wiring structure. GPS device installation (basic installation with no fuel/temperature/door sensors connected), learn the following instructions. Read more on the Do’s & Dont’s of GPS device installation at the end of this document. Screwdriver set, Plier, Multimeter and Wire Stripper/Cutter/Crimper. Before putting in the machine, you need to notice down International Mobile Equipment Identity (IMEI) number of the GPS tracking device and the SIM GSM quantity. Then insert the GPRS enabled SIM card to the device. Chances are you'll as properly obtain the vehicle addition template to record car information. Then insert the GPRS enabled SIM card to the system.
Chances are you'll as properly obtain the automobile addition template to record automobile data. IMEI is a singular number to establish GSM, WCDMA, and iDEN cellphones, satellite tv for pc phones, in addition to some telematics gadgets that works as a unique identification code. This 15-digit quantity is often printed either on the underside of the GPS monitoring unit or the machine case; you require IMEI to register the GPS tracking device on the fleet management software. Red wire (of GPS device) to one end and the ability supply of the vehicle to the other end of a 1Amp fuse. Secure the fuse to the instrument chord with a cable tie. Connect Black wire (-ve) on the harness to Chassis Ground (any bolt or wire with -ve energy). Connect Yellow ignition sense wire to the vehicle’s ignition supply to help monitor ignition ON/OFF events. Please consult the car wiring diagram to find the ignition wire.
You can verify the car ignition wire by measuring the vehicle’s working voltage while the engine is working. Once identified, connect the ignition wire to the FUSE Box with a 3M Scotchlok so that it's going to snap into place and will get it correctly seated. Please check with the connection diagram beneath, for an in depth view of the wires & connectivities. One of the quickest and the perfect place to mount a GPS tracking device or a GPS tracker is under the dashboard or an exterior location in a horizontal place with a clear view of the sky. Chances are you'll experiment with putting the tracking device at totally different locations on the vehicle to find out the very best reception for ItagPro the desired stage of concealment. If the system has external GPS antenna then place the antenna underneath the dashboard or wherever handy using double-sided sticky-tape to ensure it’s firmly fixed there. Once you’ve placed the GPS tracker in the automobile, you’re all set.
Connect the wire socket and GPS/GSM antenna (of those with external antenna) to the GPS device. As soon because the device is powered on, both green LEDs (GPS & communication) will flash on and off while looking for indicators. When full signal power is achieved, both LEDs will constantly illuminate. With a view to validate performance, we have to ring the GSM mobile number of the SIM. If it rings or responds with a busy note, you possibly can safely assume that the gadget is functioning properly. If there is no such thing as a response, it's possible you'll have to re-insert the SIM card and check the wiring once more. Please Log into the platform with your credentials to ensure the system communicates with the server. Note: Guantee that the IMEI no’s & mobile no’s you updated towards the automobiles are appropriate. To keep away from mishaps whereas installation, be certain the automobile ignition is turned off before initiating wire connections. It is always advisable to disconnect the suitable jumpers /connections of vehicle’s energy provide during the GPS device set up; this is to avoid short circuits and wiring damages.
Ensure the wires keep disconnected whereas mounting/dismounting the machine. Secure all wiring with Scotchlok, cable connectors, and electrical insulation tapes. Never enable any naked wiring to remain uncovered; connections must be least seen. Ensure extra insulation if wires go through a visible/exterior area, in order to avoid quick circuit/wiring damages. GPS monitoring gadgets might be mounted in a zone of limited entry, so none has direct access to the instrument. Keep connecting wires as discreetly as possible, making it much less visible and onerous to note. For the safety of personnel, ItagPro device & vehicle, avoid connecting machine wires to the board computers (ECU) or control models. Ensure that you fasten wires to different wires/non-moving components and not to fasten near heat emitting and transferring objects as friction/heat emission could trigger sparks leading to quick circuits. While connecting ignition wire affirm if it’s the real ignition wire (power provide available only when the ignition is on). Using a multimeter, test energy movement by turning on/off the engine.
